Get A Quote
  • English

  • French

  • German

  • Italian

  • Portuguese

  • Russian

  • Spanish

Media Blasting Services for CNC Machined Parts

DEK's media blasting services are applied to parts we machine in-house, in the same order: bead blasting, aluminum oxide, ceramic and shot peening. Blasting adds a day at most, no MOQ.

Media blasting nozzle spraying machined aluminum bracket surface
  • Ra 0.8–3 µm Typical Matte
  • AMS 2430 Peening Standard
  • ±0.005 mm Feature Tolerance

Media Blasting Services at DEK

Compressed air propels media at the machined surface, leaving a uniform, non-directional texture. Blasting is planned with the machining in the same order; no blasting-only orders.

  • 01

    CNC Machining

    DEK machines the part in-house; media, masking and the effect on a ±0.005 mm feature are set at the same engineering review.

  • 02

    Masking

    Bores with H7/g6 fits, threads, sealing faces, O-ring grooves and datum faces are masked with rubber plugs, caps, tape and fixtures.

  • 03

    Blasting or Peening

    Glass bead, ceramic, aluminum oxide, steel shot or plastic media is chosen for the material and the intended finish or fatigue goal.

  • 04

    Follow-On Finish

    A deoxidizing step precedes the anodize bath on aluminum; the anodize, chem film or passivation then runs in the same order.

  • 05

    Inspection & Records

    Almen strip results are recorded for peened parts, and cosmetic parts are photographed before shipment from our certified shop.

What Media Blasting Delivers & Where to Be Mindful

Blasting changes texture and cleanliness, not geometry. Know its strengths and limits before you specify it on a machined part.

  • Key Benefits

    • Tool marks disappear: cutter paths and step-over lines are replaced by a uniform, non-directional texture
    • Hides fingerprints: the matte surface stays clean-looking on handled housings and hardware
    • Light burrs removed: blasting knocks off light burrs left by machining
    • Clean surface: scale, heat tint and EDM recast are cleaned off before the next finish
    • Paint and powder key: aluminum oxide leaves an etched texture suited to paint adhesion
    • Longer fatigue life: shot peening adds compressive stress 0.1–0.5 mm deep
  • Limitations & Alternatives

    1. No precision improvement: blasting does not improve flatness, roundness or Ra on a precision face
    2. Smooth or bright surface: choose polishing or electropolishing on stainless; blasting goes the other way
    3. Internal passages: blasting cannot reach cross-holes; see deburring for edge work inside
    4. Small parts in volume: vibratory tumbling gives a similar matte at lower cost per piece
    5. Material removal on fits: aluminum oxide removes 5–10 µm on aluminum, so tight bores need masking
Matte bead blasted finish on machined aluminum chassis component

Matte Finish and Surface Results

Each media gives a measurable result on a machined part: texture, roughness, cleanliness or fatigue resistance, matched to the next finish.

  • Uniform Satin Matte

    Glass bead #80–#170 gives Ra 0.8–1.6 µm with negligible dimensional change (< 2 µm) on cosmetic aluminum and stainless.

  • Brighter Satin

    Ceramic bead 60–150 µm gives Ra 0.4–1.0 µm, finer and more consistent lot to lot on stainless, titanium and aluminum.

  • Etched Paint Key

    Aluminum oxide 60–220 grit leaves Ra 1.5–4 µm for paint and powder-coat adhesion and scale removal on steel and titanium.

  • Fatigue Resistance

    Shot peening closes surface micro-cracks and delays fatigue crack initiation, commonly extending fatigue life several-fold.

  • Gentle Cleaning

    Plastic media Type II / Type V, 20–40 mesh leaves Ra ≤ 0.8 µm with no dimensional change on plastics and thin aluminum.

  • Descaled Steel

    Steel shot S110–S330 gives Ra 2–6 µm with small growth; it is never used on aluminum or stainless (iron contamination).

Blasting Media Compared

Media Grit / size Resulting Ra Effect on dimensions Purpose and typical materials
Glass bead #80–#170 0.8–1.6 µm Negligible (< 2 µm) Satin matte; cosmetic aluminum and stainless; pre-anodize; light peening
Ceramic bead 60–150 µm 0.4–1.0 µm Negligible Finer, brighter satin; consistent lot to lot; stainless, titanium, aluminum
Aluminum oxide 60–220 grit 1.5–4 µm 5–10 µm removed on aluminum; edges rounded ~0.05 mm Aggressive etch; paint/powder key; descaling; steel, titanium, cast iron
Steel shot S110–S330 2–6 µm Small growth, surface dimpled Shot peening and descaling of steel; never on aluminum or stainless
Plastic media Type II / Type V, 20–40 mesh ≤ 0.8 µm None Gentle cleaning, paint stripping, deburring plastics and thin aluminum

Design & Tolerance Notes

Blasting reaches every exposed surface and can remove material, so the drawing must name the media, the surfaces, the masking and the follow-on finish.

  • Mask Critical Fits

    Mask bores and shafts with H7/g6 or tighter fits, threads, sealing faces, O-ring grooves, lapped and datum faces, plus laser-marked zones.

  • Expect Edge Rounding

    Unmasked aluminum oxide-blasted parts get a 0.05 mm edge radius; polished features lose some gloss.

  • Write the Drawing Note

    Example: "Glass bead blast #120 all external surfaces; mask bore Ø12 H7, threads and face A". Add a boundary sample where cosmetic uniformity matters.

  • Name the Follow-On Finish

    State "then anodize Type II clear" or "then passivate"; the same blast also works before black oxide on steel for a flat non-reflective black.

  • Sequence Peened Parts

    Machine, heat treat, grind, peen, then plate or coat; a light polish may remove under 10% of the compressive depth.

  • Specify Shot Peening Services

    Name the standard, media, Almen intensity, coverage and the peened surfaces on the drawing for shot peening services.

Blasting & Peening Specifications

  • Glass bead grit #80–#170 (#120 general satin)
  • Glass bead Ra 0.8–1.6 µm
  • Ceramic bead Ra 0.4–1.0 µm
  • Aluminum oxide removal 5–10 µm on aluminum
  • Bead removal < 2 µm
  • Peening depth 0.1–0.5 mm compressive
  • Almen intensity 0.008–0.012 A / 0.006–0.010 N
  • Coverage 100% min, 200% critical
  • Peening standard AMS 2430 or SAE J2441
  • Peened Ra 2–6 µm
  • Feature tolerance ±0.005 mm
  • Added lead time A day at most
  • Certifications ISO 9001:2015, ISO 13485, AS9100D

Bead Blasting and the Shot Peening Process

Two processes with different goals: bead blasting for appearance before anodizing, peening for fatigue life.

  • Bead Blasting Before Anodizing

    Bead blasting followed by anodizing is the most common request: the matte finish machined parts are known for.

    • #80: visibly coarse texture
    • #120: the general-purpose satin
    • #170: fine and slightly brighter
    • Deoxidizing step added before the anodize bath
    • Same sequence works before chem film
    Anodizing Options
    Parameter Specification
    Standard grit #120 glass bead
    Resulting Ra 0.8–1.6 µm
    Follow-on Type II clear or black
  • The Shot Peening Process

    The shot peening process drives compressive residual stress 0.1–0.5 mm deep, closing micro-cracks and delaying fatigue crack initiation.

    • Media: cast steel shot S110–S330, cut wire, ceramic or glass bead
    • Almen intensity on A, N or C strips
    • Applied to machined gears, springs and shafts
    • Common on landing gear and connecting rods
    Request a Quote
    Parameter Specification
    Compressive depth 0.1–0.5 mm
    Steel gear intensity 0.008–0.012 A
    Aluminum intensity 0.006–0.010 N
    Coverage 100% min, 200% critical
    Standard AMS 2430 or SAE J2441

Frequently Asked Questions

Answers on media choice, dimensions, anodizing and shot peening on machined parts.

What is the difference between bead blasting and sandblasting?
Bead blasting uses round glass or ceramic beads that peen the surface into a smooth satin matte with almost no material removal. Sandblasting, in practice aluminum oxide grit, cuts the surface and leaves a rougher etched texture suited to paint adhesion. DEK does not use silica sand.
Does bead blasting change part dimensions?
Barely. Glass and ceramic bead remove under 2 µm and are safe on most machined features. Aluminum oxide can remove 5–10 µm on aluminum and rounds edges, so tight fits, threads and sealing faces are masked when the drawing calls for it.
Should I bead blast before anodizing?
Yes, if you want a uniform matte finish that hides tool marks. A #120 glass bead blast followed by Type II clear or black anodize is the standard cosmetic finish on machined aluminum housings and consumer hardware.
What is shot peening and how is it different from blasting?
Shot peening bombards the surface with controlled media to build a compressive stress layer 0.1–0.5 mm deep that improves fatigue life. It is specified by Almen intensity and coverage under AMS 2430 or SAE J2441, not by appearance, and is applied to springs, gears and shafts after final grinding.
Do you blast or peen parts I machined elsewhere?
No. DEK applies media blasting and shot peening only to parts it machines in-house, as part of the same order, so masking and follow-on finishes are planned with the machining from the start.